We are having a hard time getting T54S for installs (back-order after back-order). One vendor said these are being discontinued; is this true? They have only been out for what...one year?
↧
T54S Backorder Discontinued?
↧
Upgrade firmware via Action URI
Hi
is it possible to remotely upgrade a T4xx handset via Action URI and tell it which firmware to go and download and where to download it from ?
Thanks
is it possible to remotely upgrade a T4xx handset via Action URI and tell it which firmware to go and download and where to download it from ?
Thanks
↧
↧
V84 Firmware Model Support
Hi,
I have noticed that V84 firmware has been released for some models of telephone, but not others.
For example, we have deployed CP920, T19P E2, T40G which are supported, however Our T41P and T46G are still showing V83 as the latest for their download support pages.
Are the T41P and T46G telephones discontinued, or will these models have V84 released later on?
I have noticed that V84 firmware has been released for some models of telephone, but not others.
For example, we have deployed CP920, T19P E2, T40G which are supported, however Our T41P and T46G are still showing V83 as the latest for their download support pages.
Are the T41P and T46G telephones discontinued, or will these models have V84 released later on?
↧
Odd Behavior with Static IPs
I've had a few phones seem to loose their ability to find their way off the local subnet with our refreshing the network info, the PBX is on a different subnet, I can ping/get on the web interface via the local subnet but not from the subnet the PBX is on. (I worked around this to update by using ssh tunneling and resigning ports when fixing it). To resolve all I did was add a new dns entry (added 8.8.8.8 though this device is not able to access the internet). After the device rebooted it was fine, a normal powercycle did not fix it.
↧
Assign static IP to WF40?
I am using a WF40 wireless network card on a T42s.
Is it possible to assign a static IP to it?
If so, can this be done manually by pressing buttons on the phone?
Is it possible to assign a static IP to it?
If so, can this be done manually by pressing buttons on the phone?
↧
↧
Firmware T46G Version 84
Hi,
I noticed there is no T46-28.84.0.10 firmware release, is there one to come?
thx
I noticed there is no T46-28.84.0.10 firmware release, is there one to come?
thx
↧
T46S SfB CAP always uses PSTN
Hello all,
we recently configured a T46S SfB in CAP mode (SfB online from Office365 tenant). Of course the corresponding O365 account has the required licenses, too.
But if we now want to call another user from the same tenant, the phone uses only his landline number, not starting a Skype call.
I select the target from the dictionary, and although I see both landline number and e-mail address in the entry, the phone uses only the landline.
And if I delete the landline from the contact and then try to start a call, the phone says "no number" (or similar), although the e-mail address is still valid.
Maybe my expectation is wrong, but I do expect that a Skype phone, regardless of Skype client on PC or desk-phone, always prefers the Skype connected call over the PSTN one.
Can anyone shed some light on this?
Thanks, Sebastian
we recently configured a T46S SfB in CAP mode (SfB online from Office365 tenant). Of course the corresponding O365 account has the required licenses, too.
But if we now want to call another user from the same tenant, the phone uses only his landline number, not starting a Skype call.
I select the target from the dictionary, and although I see both landline number and e-mail address in the entry, the phone uses only the landline.
And if I delete the landline from the contact and then try to start a call, the phone says "no number" (or similar), although the e-mail address is still valid.
Maybe my expectation is wrong, but I do expect that a Skype phone, regardless of Skype client on PC or desk-phone, always prefers the Skype connected call over the PSTN one.
Can anyone shed some light on this?
Thanks, Sebastian
↧
EXP50 BLF user status not changing
I have three side EXP50 units connected to a T58A and have users configured in each of the key fields for BLF with value of their extension, the label is their name, and all set to default line 1. No extension is configured.
The unit shows when they are on the phone, but not when in DND or Away status. Am I missing something to make this work properly to show at least the DND status on the units?
This was a big decision on why we got the three additional units so our receptionist can see who is on the phone and in/out of the office at a glance.
Thanks for any info!
James
The unit shows when they are on the phone, but not when in DND or Away status. Am I missing something to make this work properly to show at least the DND status on the units?
This was a big decision on why we got the three additional units so our receptionist can see who is on the phone and in/out of the office at a glance.
Thanks for any info!
James
↧
EHS 36 Firmware
Should all EHS36 be upgraded to 3.16?
Are they backwards compatible?
Meaning if its being used for a T46 today and we upgrade it and next week we move it to a T26 will it work or we need to downgrade?
Any reason Yealink never found a simpler way of upgrading it? (for example even a hidden GUI page that we can directly update to or URL..
Thanks!
Are they backwards compatible?
Meaning if its being used for a T46 today and we upgrade it and next week we move it to a T26 will it work or we need to downgrade?
Any reason Yealink never found a simpler way of upgrading it? (for example even a hidden GUI page that we can directly update to or URL..
Thanks!
↧
↧
CDP enable after factory reset cause the phone can't obtain IP address
I have a situation here after upgrading to latest V83 firmware on my T23G phone.
Previously, each time I reset to factory, the phone can obtain IP address from DHCP service without problem.
Recently, I discover that reset to factory, some phone can obtain IP address but some phone can't.
After further investigation, I notice those phone connect directly to core switch can get IP address. For those phone connect to access switch or nested switch, it can't get the IP address.
I further notice that if the cdp was enable in this new firmware. If I set the cdp enable to false explicitly after factory reset, I can get IP address for phones connected to access switch.
Please rectify this problem.
Thank you.
Previously, each time I reset to factory, the phone can obtain IP address from DHCP service without problem.
Recently, I discover that reset to factory, some phone can obtain IP address but some phone can't.
After further investigation, I notice those phone connect directly to core switch can get IP address. For those phone connect to access switch or nested switch, it can't get the IP address.
I further notice that if the cdp was enable in this new firmware. If I set the cdp enable to false explicitly after factory reset, I can get IP address for phones connected to access switch.
Please rectify this problem.
Thank you.
↧
W52P admin pass after recovery
Hi,
I have problem with login to w52p after i put recovery rom.
Admin and pass are not right "admin/admin" and after searching all day nothing helped me...
Please help![Sad]( "Sad")
I have problem with login to w52p after i put recovery rom.
Admin and pass are not right "admin/admin" and after searching all day nothing helped me...
Please help
↧
BLF no longer works when recovered from Failover Server
I submitted a ticket on this issue which I have pasted below. Basically when my T46s, T46g, and T48s's failover to the secondary server the BLF function works fine. However when the primary server becomes available again and the phones fail back to the production server they no longer will see BLF lights anymore. You can still park the calls on those positions but the BLF is broken until you reboot the phones. I am using 60TTL DNS failover with 1 DNS name and 2 servers with 2 ip's. I have added the additional troubleshooting below. Hope someone has fixed this.
T46s registered to ServerA. ServerA has a failure and DNS forces the T46s to register to ServerB
On ServerB the T46s works fine as expected
Once ServerA becomes available again DNS force the T46s to register back to ServerA
T46s BLF for parked calls no longer lights up when used
T46s is rebooted and BLF starts to function properly again
I have 45 of these devices im testing with and all of them have this issue
I have Sangoma S500's with the same setup and did not exhibit this issue
So I have done some further testing.
I tried enabling the account.x.subscribe.register = 1 (enable). This cause dual registrations and had no effect on the issue of BLF not functioning when failed back to primary server.
I lowered the Subscribe Period from 1800s to 30s to see if that would make a difference. I waited up to 7 minutes after failover back to primary server and BLF functionality never recovered.
I upgraded the firmware on my T48s to 66.84.0.10 to see if that would make a difference. No change with this
I have tested this with T48s, T46g,T46s up to 65 endpoints and none of them can recover the BLF functions after failing back to primary server.
Thank you,
Claudio
T46s registered to ServerA. ServerA has a failure and DNS forces the T46s to register to ServerB
On ServerB the T46s works fine as expected
Once ServerA becomes available again DNS force the T46s to register back to ServerA
T46s BLF for parked calls no longer lights up when used
T46s is rebooted and BLF starts to function properly again
I have 45 of these devices im testing with and all of them have this issue
I have Sangoma S500's with the same setup and did not exhibit this issue
So I have done some further testing.
I tried enabling the account.x.subscribe.register = 1 (enable). This cause dual registrations and had no effect on the issue of BLF not functioning when failed back to primary server.
I lowered the Subscribe Period from 1800s to 30s to see if that would make a difference. I waited up to 7 minutes after failover back to primary server and BLF functionality never recovered.
I upgraded the firmware on my T48s to 66.84.0.10 to see if that would make a difference. No change with this
I have tested this with T48s, T46g,T46s up to 65 endpoints and none of them can recover the BLF functions after failing back to primary server.
Thank you,
Claudio
↧
Unable to logon to phone web page
Hi,
Whenever i try to logon to the phone's web page i cannot press confirm
This only happens with the T40P, if i try with any other model it works fine.
When i open the web console i get the following message
![[Image: mYbAWpB.jpg]]()
Whenever i try to logon to the phone's web page i cannot press confirm
This only happens with the T40P, if i try with any other model it works fine.
When i open the web console i get the following message
![[Image: mYbAWpB.jpg]](http://i.imgur.com/mYbAWpB.jpg)
↧
↧
T46S Speed dial problem
Strange problem here:
On a T46S with 66.84.0.10 firmware, I programmed a speeddial DSSKey with an external number. When I use it, I hear about one second of sound then the call becomes silent (but doesn't hangup).
If I dial the same number manually, everything is fine. I was able to reproduce the problem on 2 different systems (FreePBX) with 2 different T46s phones. For now, I only have one phone number that does this. It's probably related to the phone system of the person I'm calling, but the fact that everything is fine when not using the DSSKey speeddial is really strange.
Is there a difference between a speeddial and dialing a call manually ?
Ok I just found out something while analysing a capture: the speeddial DSS Key adds ** after calling. When dialing manually, I don't see the **
The FreePBX log confirms this:
DTMF begin '*' received on SIP/206-000056f4
DTMF begin passthrough '*' on SIP/206-000056f4
DTMF end '*' received on SIP/206-000056f4, duration 100 ms
DTMF end accepted with begin '*' on SIP/206-000056f4
DTMF end passthrough '*' on SIP/206-000056f4
DTMF begin '*' received on SIP/206-000056f4
DTMF begin passthrough '*' on SIP/206-000056f4
DTMF end '*' received on SIP/206-000056f4, duration 100 ms
DTMF end accepted with begin '*' on SIP/206-000056f4
DTMF end passthrough '*' on SIP/206-000056f4
On a T46S with 66.84.0.10 firmware, I programmed a speeddial DSSKey with an external number. When I use it, I hear about one second of sound then the call becomes silent (but doesn't hangup).
If I dial the same number manually, everything is fine. I was able to reproduce the problem on 2 different systems (FreePBX) with 2 different T46s phones. For now, I only have one phone number that does this. It's probably related to the phone system of the person I'm calling, but the fact that everything is fine when not using the DSSKey speeddial is really strange.
Is there a difference between a speeddial and dialing a call manually ?
Ok I just found out something while analysing a capture: the speeddial DSS Key adds ** after calling. When dialing manually, I don't see the **
The FreePBX log confirms this:
DTMF begin '*' received on SIP/206-000056f4
DTMF begin passthrough '*' on SIP/206-000056f4
DTMF end '*' received on SIP/206-000056f4, duration 100 ms
DTMF end accepted with begin '*' on SIP/206-000056f4
DTMF end passthrough '*' on SIP/206-000056f4
DTMF begin '*' received on SIP/206-000056f4
DTMF begin passthrough '*' on SIP/206-000056f4
DTMF end '*' received on SIP/206-000056f4, duration 100 ms
DTMF end accepted with begin '*' on SIP/206-000056f4
DTMF end passthrough '*' on SIP/206-000056f4
↧
T48G
Hi Folks,
we run a bunch of several Yealink Phones. T46G and T52P
How do I make those phones aks for what Line to place an outgoing call on? (we got 8 currently)
I know from my Gigaset DX800A that it could be choosen an standard account to call from, or ask befor every call.
Reson is, our emploees are asked to chosse different outgoing linse if they call for one of our customers.
but they most often dont do it. (forget it) and call from our company account instead of the customers account.
so the customer sees the wrong call ID. (ours) and not the customers
That is VERRY unCOOL and intimidating for us and our customer.
so what could I do in the phone config to prevent such misshaps.
Thanks
Cheers
Manne
we run a bunch of several Yealink Phones. T46G and T52P
How do I make those phones aks for what Line to place an outgoing call on? (we got 8 currently)
I know from my Gigaset DX800A that it could be choosen an standard account to call from, or ask befor every call.
Reson is, our emploees are asked to chosse different outgoing linse if they call for one of our customers.
but they most often dont do it. (forget it) and call from our company account instead of the customers account.
so the customer sees the wrong call ID. (ours) and not the customers
That is VERRY unCOOL and intimidating for us and our customer.
so what could I do in the phone config to prevent such misshaps.
Thanks
Cheers
Manne
↧
mail change
Folks,
how do i change my mail addrss in this funny board ware?
if i go to profile edit, it redirects my to the main forum page... :-(
funny board.
and please dumpt that f**cking captcha thing. it is very annoing to not be able to use my password safe for login and have to type it for every post.
cheers
Manne
how do i change my mail addrss in this funny board ware?
if i go to profile edit, it redirects my to the main forum page... :-(
funny board.
and please dumpt that f**cking captcha thing. it is very annoing to not be able to use my password safe for login and have to type it for every post.
cheers
Manne
↧
W60B and W56H - can you PIN lock the phones,.. ?
hello all,
we have about 20 W60B bases and at least 6 phones per base.
these are all on different locations and i was wondering if there is a way to secure the handsets a little bit better.
at the end of the day i would like to lock the phones down little bit more.
for example, i would like to dial the number on the handset, hand it over to the user WITHOUT them being able to walk away, hang up and dial a different number.
is there a way to disable users to delete the history of dialed numbers?
is there a way to PIN lock the phone down. i see the option when logged in the GUI of the W60B base but PIN lock doesn't do anything on the handset itself.
looks like these phones have great potential.
any help would be greatly appreciated.
thank you!
we have about 20 W60B bases and at least 6 phones per base.
these are all on different locations and i was wondering if there is a way to secure the handsets a little bit better.
at the end of the day i would like to lock the phones down little bit more.
for example, i would like to dial the number on the handset, hand it over to the user WITHOUT them being able to walk away, hang up and dial a different number.
is there a way to disable users to delete the history of dialed numbers?
is there a way to PIN lock the phone down. i see the option when logged in the GUI of the W60B base but PIN lock doesn't do anything on the handset itself.
looks like these phones have great potential.
any help would be greatly appreciated.
thank you!
↧
↧
Upgrade firmware with SIP Messages ?
Hi
I know I can use SIP NOTIFY to reboot and Auto Provision a phone, is it possible to send a SIP NOTIFY message to a phone with a URL and firmware file for it to upgrade ?
Thanks
I know I can use SIP NOTIFY to reboot and Auto Provision a phone, is it possible to send a SIP NOTIFY message to a phone with a URL and firmware file for it to upgrade ?
Thanks
↧
GMS core package needed
Hi there
Could anyone provide the correct GMS core package (open_gapps-arm-5.1-pico-20170713.zip ??) for the T58V?
I tried to install the latest openGapps 5.1 arm-pico from https://opengapps.org, but it didn't install![Huh]( "Huh")
Thanks a lot!
Could anyone provide the correct GMS core package (open_gapps-arm-5.1-pico-20170713.zip ??) for the T58V?
I tried to install the latest openGapps 5.1 arm-pico from https://opengapps.org, but it didn't install
Thanks a lot!
↧
custom ringtone with new BLF audio alert
REPOST IN DIFFERENT SECTION
Chaps,
this is related to the feature request for BLF audio alert I raised. that was fulfilled in firmware 66.84.0.10 - it works really well, BUT.
I;ve tried to attach a custom ring tone (actually a doorbell sound) and this does not work. The wav file for the custom ring works as a direct ring on on another phone at a lower software, so I think my wav file is ok.
This works ok with Ring8.wav
features.pickup.blf_audio_enable = 1
features.pickup.blf_visual.list =
features.pickup.blf_audio.list = 2001
features.blf.ring_type = Ring8.wav
But when i substitute the custom ring file
fetures.blf.ring_type = Doorbell3.wav
No sound emerges - I;ve checked the phone to see that the custom file is loaded.
I have a feeling it should be
fetures.blf.ring_type = XXXXXX: Doorbell3.wav
but cant find anything in the admin guide.
chris
Chaps,
this is related to the feature request for BLF audio alert I raised. that was fulfilled in firmware 66.84.0.10 - it works really well, BUT.
I;ve tried to attach a custom ring tone (actually a doorbell sound) and this does not work. The wav file for the custom ring works as a direct ring on on another phone at a lower software, so I think my wav file is ok.
This works ok with Ring8.wav
features.pickup.blf_audio_enable = 1
features.pickup.blf_visual.list =
features.pickup.blf_audio.list = 2001
features.blf.ring_type = Ring8.wav
But when i substitute the custom ring file
fetures.blf.ring_type = Doorbell3.wav
No sound emerges - I;ve checked the phone to see that the custom file is loaded.
I have a feeling it should be
fetures.blf.ring_type = XXXXXX: Doorbell3.wav
but cant find anything in the admin guide.
chris
↧
